Multi-Cylinder Hydraulic Cone Crusher Cavity Type Selection

Nowadays, there is a type of crusher that often appears in the sand and gravel production line, that is, the multi-cylinder hydraulic cone crusher. The multi-cylinder hydraulic cone crusher is a device designed based on the theory of laminated crushing. Many users asked me: “How to choose the cavity type of the multi-cylinder hydraulic cone crusher?” Then let’s solve the doubts in everyone’s mind. The multi-cylinder cone crusher parameter table is for your reference.

Multi-Cylinder Hydraulic Cone Crusher Parameter Table

Shibang Group has many models of multi-cylinder hydraulic cone crushers, which can meet different production requirements. For large, medium and small users, we can provide them with suitable models. At the same time, the cavity type is mainly divided into S1, S2, S3, H1, H2, and H3 different models. Let’s take a look at the detailed parameter table.

Each different model of multi-cylinder hydraulic cone crusher has a different cavity type, so how to choose the cavity type? Choosing the right cavity type is undoubtedly very critical for sand and gravel production. It can not only improve the crushing efficiency, but also improve the quality of the output. Without further ado, let’s take a look at it below.

How To Choose The Cavity Type For A Multi-Cylinder Hydraulic Cone Crusher?

1. According to the particle size and abrasiveness of the feed

The tight-side feed port of the crusher cannot be less than the maximum feed particle size. The feed port cannot be too large or too small.

If the feed port is too large:

The material is mainly concentrated in the lower part of the crushing chamber, causing excessive wear on the lower part of the liner and low liner utilization.

If the feed port is too small:

① The material cannot enter the crushing chamber, the production capacity is seriously reduced, and the feed port liner is severely worn or even destroyed.

② It causes large fluctuations in crushing force and adjustment ring jump, causing damage to the frame seat gasket, accelerating the wear of the locking cylinder seal, and affecting the stability of the equipment.

2. According To The Particle Shape And Particle Size Of The Discharge Material

The product particle size depends on whether the crushing process is open-circuit crushing or closed-circuit crushing.

① Generally speaking, the tight-side discharge port of the crusher is equal to the sieve hole size or slightly larger than the average particle size of the required product. Each cavity type has a minimum discharge port, and the minimum discharge port should be avoided when selecting the cavity type.

②When the fixed cone thread enters the adjustment ring 1.5 teeth, the discharge port is the maximum discharge port (the fixed cone thread must be screwed into the adjustment ring for at least 1.5 teeth, otherwise it is easy to cause equipment failure).

③Relatively speaking, a small crushing cavity can set a smaller discharge port and better adjust the discharge port. A small crushing cavity is easier to obtain a good particle shape. In terms of product particle shape, the short-head type crushing cavity can obtain a better product particle shape, followed by the standard fine cavity type. In order to ensure a good product particle shape, the crushing ratio should be controlled at 3 to 3.5.

Multi-cylinder hydraulic cone crusher requires a good crushing system plus the correct cavity selection and standardized operation methods to maximize the value of the multi-cylinder hydraulic cone crusher. Therefore, it is recommended that you should also consider many aspects when choosing. For your convenience, you can directly consult the Shibang technical manager online for free to tailor the options for you one-to-one.

How Much Does A Multi-Cylinder Hydraulic Cone Crusher Cost? Recommended Manufacturers

If you want to know how much a multi-cylinder hydraulic cone crusher costs, we cannot give a fixed value here. The price can only be determined based on the specific model selected. The market price is usually around 100,000 to 800,000 yuan. The price of a cone crusher is related to the production cost, including the selected material and production process. There are differences among different manufacturers, so it is recommended that you choose a powerful manufacturer.

For example, Shibang Group has more than 30 years of production experience. Each device has been checked layer by layer, and the quality is guaranteed. There will be no frequent failures in the later operation. In addition, Shibang Group has a professional after-sales team, which regularly maintains and maintains the equipment, which will reduce a lot of trouble for your later operation. You are welcome to come to Shibang for free inspection at any time.